How Much Does Gate Installation Cost in Irving?
Gate installation in Irving, TX typically costs between $1,200 and $8,500, depending on gate type, material, linear footage, and whether you’re adding an automated opener and access control system. A straightforward single-swing driveway gate with a basic LiftMaster or Mighty Mule operator lands toward the lower end; a dual-swing or slide gate with keypad entry, video intercom, and custom welded ironwork pushes toward the top. Most Irving homeowners investing in a mid-range automated gate — powder-coated steel, single slide, standard operator — pay somewhere in the $2,800–$4,500 range installed.
Gate Installation Cost Breakdown (2026)
Below are the real price ranges Dennis Price and his team see on jobs across Irving — from Las Colinas townhome driveways to commercial properties along Beltline Road. These reflect materials, labor, and operator installation as a package. Permit fees (City of Irving building permits for fence and gate structures run roughly $50–$150 for residential projects) are separate and depend on scope.
| Gate Type / Scope | Typical Installed Price Range (Irving, 2026) |
|---|---|
| Manual swing gate (single, steel or iron) | $1,200 – $2,200 |
| Automated single-swing gate with operator | $2,000 – $3,800 |
| Automated dual-swing gate with operator | $3,200 – $5,500 |
| Slide/roll gate (residential, up to 16 ft) | $2,800 – $4,800 |
| Slide/roll gate (commercial, 16–30 ft) | $4,500 – $8,500 |
| Ornamental iron or custom-fabricated gate (panel only) | $900 – $3,500 |
| Gate operator / motor only (LiftMaster, FAAC, Viking, etc.) | $650 – $1,800 |
| Access control add-on (keypad, intercom, or card reader) | $350 – $1,200 |
| Concrete pad or footer work for posts | $250 – $700 |
| Solar panel add-on for remote operator | $180 – $450 |
The biggest variable in Irving isn’t the gate itself — it’s the ground. Expansive clay soil is common across much of Irving, including older neighborhoods near North Lake and around the Heritage District. That clay shifts seasonally, which means post footings need to go deeper than the standard 24 inches you’d spec in a drier market. Dennis regularly pours 30–36 inch footings on Irving installs to keep posts plumb through summer heat cycles. That adds concrete and labor cost, but it’s the difference between a gate that swings true in year five and one that’s already racking out of square.
What Affects Gate Installation Pricing in Irving
- Gate size and linear footage: A 10-foot driveway opening and a 24-foot commercial entrance are not in the same price universe. Every additional foot of gate panel means more steel, more weld time, and a heavier operator to move it reliably. In Irving’s newer mixed-use developments near Toyota Music Factory, wider entrance openings for dual-lane commercial access are increasingly common — and they drive costs up fast.
- Material choice: Tubular steel and ornamental iron are the Irving market standard because they hold up to North Texas heat without the warping you’d see in wood. Powder-coated steel is the most popular mid-range option. Aluminum costs less upfront but tends to need operator recalibration more often as it flexes. Custom wrought iron with decorative scrollwork — common in Las Colinas estate communities — can add $800–$1,500 in fabrication time alone.
- Automation and operator brand: A Ghost Controls solar kit costs far less installed than a FAAC underground system designed for heavy commercial use, but they serve completely different applications. Dennis is experienced across LiftMaster, Viking, BFT, Linear, DoorKing, Elite, and six other brands — which matters because specifying the right operator for your gate’s weight and duty cycle is where cheap installs fall apart within two years.
- Access control complexity: A single-button remote adds almost nothing to the cost. A DoorKing telephone entry system wired to a multi-tenant property in Irving’s commercial corridor adds $600–$1,200 in hardware and programming time. Keypad-only entry lands in the middle. If you’re managing an HOA or apartment complex, expect this line item to be significant.
- Existing infrastructure: Installing a gate where posts already exist is straightforward. Installing on raw property without conduit, without a 110V or 120V outlet near the gate location, and without existing concrete at the threshold adds real cost — typically $300–$800 in electrical rough-in and concrete work before the gate ever goes up.
- Local permit requirements: The City of Irving requires a building permit for structural fence and gate installations that exceed certain height thresholds or sit on commercial property. Pulling the permit, scheduling the inspection, and ensuring the install meets Irving’s setback rules adds time to the project. Dennis’s team handles permit coordination — it’s not a surprise line item, but it is a real one.
How to Save on Gate Installation
The most reliable way to save money on a gate installation in Irving is to avoid paying twice. That sounds obvious, but the pattern is predictable: a homeowner in Valley Ranch or Hackberry Creek picks the lowest bid from a handyman service, the posts go in without proper footings, the operator is undersized for the gate weight, and within 18 months the gate is out of alignment, the operator is burning out, and now they’re calling Dennis to fix what was done wrong the first time. A properly engineered install, done once, beats two installs at a discount.
That said, there are genuinely smart ways to manage cost:
- Choose the right operator for your gate — not the cheapest one on the shelf. A Mighty Mule is a solid residential operator for lighter aluminum gates. Hanging it on a 400-pound steel swing gate because it costs $200 less than the right Viking or LiftMaster unit is a false economy. Dennis will tell you exactly which operator matches your gate’s weight and your usage volume — that conversation is free.
- Start with the gate, add access control later. Run conduit to the post during installation even if you’re not wiring the keypad or intercom yet. Conduit costs almost nothing when the ground is already open. Trenching for it a year later costs $200–$400 more. Plan ahead in the rough-in stage and add the tech on your timeline.
- Combine jobs if you’re also doing fence work. If your fence posts are going in at the same time, post spacing and concrete pours can be coordinated to reduce labor. Dennis can assess whether it makes sense to sequence the work together.
- Get a free estimate before committing to a scope. Prices in this guide reflect the Irving market range, but your specific property — lot grade, gate opening width, soil condition, and existing electrical access — determines your actual number. Call (855) 914-8517 and Dennis will walk the site and give you a written estimate at no charge. That’s not a teaser; it’s how every job starts.
FAQs — Gate Installation Cost in Irving, TX
How much does a basic automated driveway gate cost in Irving?
A basic automated driveway gate in Irving — single swing, powder-coated steel, standard LiftMaster or Mighty Mule operator, and a single remote — typically runs $2,000–$3,200 installed. That range assumes a standard 10–12 foot opening, reasonable soil conditions, and an existing power source nearby. If you need deeper footings (common in Irving’s clay-heavy areas) or electrical rough-in, budget another $300–$600. Call (855) 914-8517 for a free on-site estimate specific to your property.
Is a slide gate or swing gate more expensive to install in Irving?
Slide gates generally cost $300–$800 more to install than comparable swing gates because they require a concrete track, a counterweight or cantilever track system, and a more robust operator to handle lateral movement. That said, in Irving driveways where there isn’t enough setback on either side for a swing gate to open fully, a slide gate is often the only practical option — and the cost difference is worth it to avoid a gate that won’t open completely. Dennis evaluates your driveway geometry during the free estimate and recommends the configuration that actually works for your space.
Does Everest Gate Repair Service pull permits for Irving gate installations?
Yes. For commercial installs and residential projects that meet the City of Irving’s threshold for structural permitting, Dennis and his team handle permit coordination. Residential permit fees in Irving typically run $50–$150; commercial permits vary by project scope. Permit costs are included in your written estimate — they won’t appear as a surprise line item when the job is done. Call (855) 914-8517 to discuss what your specific project requires.
How long does gate installation take in Irving?
Most residential gate installations in Irving are completed in one day — typically 4–8 hours depending on whether concrete work is required. If new concrete footings need to cure, the operator and gate panel may be installed the following day after a 24-hour set period. Commercial projects with trenching, access control wiring, or custom fabrication can run 2–3 days. Dennis schedules efficiently because he’s both the decision-maker and the technician on the job — there’s no waiting for a supervisor to approve a field change.
Is it cheaper to repair an old gate or install a new one in Irving?
Repair is almost always cheaper if the gate structure is sound and the operator is the failing component. Replacing a gate operator in Irving typically costs $650–$1,400 depending on brand and gate weight — significantly less than a full installation at $2,000+. Where replacement becomes the smarter investment is when the gate panel itself is severely corroded, structurally racked, or the posts have shifted enough that no operator will run it reliably. Dennis assesses this honestly: if repair makes financial sense for your situation, that’s what he’ll tell you, not what sells a bigger job. Call (855) 914-8517 for a straight answer.
Why Irving Property Owners Work With Everest Gate Repair Service
Dennis Price has been working gates in the Dallas–Fort Worth area for 11 consecutive years — not as a sideline to general contracting or handyman work, but as his exclusive specialty. That focus matters in a market like Irving, where you’ll find everything from 1970s-era manual swing gates in older residential neighborhoods near Story Road to sophisticated FAAC and DoorKing-controlled commercial entrances along the SH 183 corridor. The range of what exists in this city means generic experience doesn’t cut it.
When Dennis shows up on an Irving install, he’s carrying experience across nine gate operator brands — LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule — along with in-house welding capability for structural repairs and custom fabrication. If a gate panel needs modification to fit a non-standard opening, that work happens on-site, not at a separate metal shop with a separate timeline and a separate invoice.
707 verified reviews averaging 4.8 stars aren’t a marketing headline — they’re the accumulated record of thousands of jobs where the gate worked correctly when Dennis left the property. If you’re comparing quotes for a gate installation in Irving, you can read what those customers actually said. The track record speaks more accurately than any claim we could write here.
For homeowners elsewhere in the region, we also offer Gate Installation in Fort Worth with the same owner-operated approach and multi-brand expertise. And if you’d like to learn more about what Everest Gate Repair Service covers across the Dallas–Fort Worth area, visit our home page for the full picture.
Get a Free Gate Installation Estimate in Irving
If you’re pricing a gate installation in Irving — whether it’s a straightforward residential driveway gate or a multi-access commercial entrance — the most useful thing you can do is get an actual number for your specific property rather than working from ranges. Dennis Price will walk your site, measure your opening, assess your soil and electrical situation, and give you a written estimate at no charge.
Call (855) 914-8517 to schedule your free estimate. Most Irving jobs can be assessed within the week, and installation is typically scheduled shortly after. No pressure, no upselling — just a straight number from the person who will actually do the work.
Written by Dennis Price, Owner at Everest Gate Repair Service Dallas Fort Worth, serving Irving, TX since 2014.
Pricing reflects the Irving market as of 2026. Everest Gate Repair Service Dallas Fort Worth offers free estimates — call (855) 914-8517.