Fast, Reliable Gate Installation Across Keller
Gate installation in Keller, TX typically runs $2,800–$7,500 for a complete automated driveway system, and most projects are completed in 1–3 days once materials arrive. We’re based in Irving and regularly make the run up to Keller — usually within 45 minutes for estimates, and we carry common LiftMaster, FAAC, and DoorKing hardware so we’re not waiting on freight.
Keller’s a different animal than most DFW suburbs. The lots are bigger, the gates are wider, and a lot of what got installed in the 2005–2010 build boom is hitting the wall right now. Dennis and his team have spent eleven years specializing exclusively in gates, and we’ve learned that Gate Installation in Keller isn’t about dropping in a standard kit — it’s about engineering for black clay soil, triple-digit heat, and driveways that stretch a lot farther than the original builder anticipated.
Why Everest Gate Repair Service Dallas Fort Worth Is Keller’s Preferred Gate Installation Company
We’ve got 707 verified reviews averaging 4.8 stars, and a solid chunk of those come from Keller homeowners who found us after the second or third “repair” from a general handyman didn’t stick. Dennis Price shows up personally — he’s the owner and the lead technician on every job, not a subcontractor learning on your gate. That matters when you’re diagnosing whether a grinding operator is a simple gear issue or a symptom of an undersized motor that’s been overloaded for fifteen years.
Our response time to Keller is typically same-day or next-day for estimates, and we keep parts in stock for the nine brands we service — LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. No trial-and-error ordering. No “we’ll come back when the part gets here.”
We also weld. In-house. That’s rarer than you’d think, and it’s critical in Keller where black clay heave can crack hinge posts or twist ornamental iron frames. We fix structural damage on-site instead of farming it out to a metal shop for two weeks.
Our Gate Installation Services in Keller
Driveway Gate Installation
Keller’s master-planned communities — think along Keller-Smithfield Road or in the 76248 zip — were built with generous setbacks and wide approaches. We’ve measured driveways out by Bear Creek Parkway that run 22 feet across, yet the original builder spec’d a residential-grade operator rated for 16 feet. That gap kills motors. Our driveway gate installations in Keller start with proper load calculation: gate weight, wind load, cycle frequency, and actual span. Then we size the operator correctly, usually a commercial-grade unit that won’t flinch at a 6-foot gate leaf in a Texas wind.
Swing Gate Installation
Single-leaf and dual-leaf swing gates dominate Keller’s older subdivisions — the 1990s and 2000s builds around Mount Gilead Road and Rufe Snow Drive. These systems fail predictably: hinge posts tilt in expanding clay, gate arms bind, operators grind. We install swing gates with deeper post anchoring — 42 inches minimum into black clay, often with concrete piers — and we brace ornamental iron frames at the factory level, not as an afterthought. A properly installed swing gate in Keller should open smoothly even after a week of August drought followed by a September gully-washer.
Sliding Gate Installation
Sliding gates make sense on Keller’s sloped lots and curved driveways where a swing arc won’t work. But the track system is unforgiving. We’ve replaced slide gates in the 76244 area where the original track was set on a concrete pad that heaved seasonally, throwing the v-groove wheels off alignment and shredding the rack gear. Our sliding gate installations include adjustable track mounts, proper drainage planning, and operators sized for the actual gate mass — not the catalog guess.
Pedestrian Gate Installation
Not every gate in Keller is for cars. We install matching pedestrian gates alongside driveway systems — wrought iron walk-throughs with keypad or fob access, integrated into the same access control network. These get heavy use in Keller’s active neighborhoods, and we build them to the same structural standard as the main gate, not as a flimsy afterthought.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Keller
We work on nine major brands — LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule — and we stock parts for the ones we see most in Keller. LiftMaster and FAAC dominate the residential automatic market here; DoorKing and Elite show up frequently on HOA and commercial entrances. Because Dennis carries inventory and knows these systems cold, we don’t guess at diagnostics. We identify your brand, pull the correct gear kit or control board, and get it running. Fast turnaround means your gate isn’t stuck open for a week while you wait for a part from California.
Common Gate Installation Problems We See in Keller Homes
- Undersized operators on oversized gates. Keller’s lots are well above DFW average, and many driveway spans exceed 20 feet. Builder-installed residential operators — often Mighty Mule or entry-level LiftMaster units — were never rated for the actual load. The motor overheats, gears strip, and the homeowner gets told “it just needs a tune-up” three times before someone measures the gate.
- Clay soil heave throwing posts out of plumb. North Texas black clay expands and contracts dramatically with moisture. We’ve found hinge posts tilted 3 degrees off vertical in Keller subdivisions, binding gate arms and bending operator brackets. Proper installation accounts for this with deeper footings and adjustable hardware.
- Ornamental iron frames sagging without adequate bracing. Builder-grade gates in Keller’s 2000s-era homes often lack diagonal bracing or welded corner gussets. Automated operation adds cyclic stress, and within five years the frame racks, latches misalign, and the operator fights itself.
- UV degradation of exposed electronics. Keller’s summer heat routinely hits 105°F, and operators mounted in direct sun — common on south-facing driveways near Keller Parkway — suffer cracked housings, brittle wiring insulation, and failed limit-switch boots. We spec UV-resistant enclosures and shade-mounted control boxes where possible.
Pricing for Gate Installation in Keller, TX
A typical manual pedestrian gate installation in Keller runs $1,200–$2,400. Automated single-leaf swing gates start around $2,800–$4,500 installed, while dual-leaf systems with commercial-grade operators land in the $4,200–$6,800 range. Sliding gates with track, motor, and access control typically run $5,500–$7,500 depending on span and material. These are 2024–2025 Keller market ranges — your actual cost depends on gate material (aluminum vs. steel vs. ornamental iron), operator brand and horsepower, access control features, and whether we need to demo and remove an existing system.
We don’t do ballpark-over-the-phone pricing. Dennis comes out, measures your actual span, checks post condition and soil type, and gives you a written estimate with line-item breakdown. Estimates are free. Call (855) 914-8517 to schedule.
We Also Serve Cities Near Keller
Our service radius covers the full northern Tarrant County corridor. We regularly install and repair gates in Watauga, North Richland Hills, Roanoke, and Saginaw — same response standards, same Dennis Price on-site, same stocked parts.
Serving Keller, TX — Our Local Coverage Area
We’re based in the Keller area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs — Gate Installation in Keller
Replace the whole system. At 18 years, you’re past the reliable lifespan of both the operator and likely the gate frame’s original bracing. We find that motors this age in Keller were often undersized for the actual gate span from day one, so a new motor on a compromised frame just delays the inevitable. Dennis will assess whether the posts and frame are sound; if they are, we can reuse them with a properly sized modern operator. Call (855) 914-8517 for a free evaluation.
Your hinge posts are shifting in expansive clay soil. After rainfall, black clay swells and tilts posts out of plumb; as it dries, they may settle back unevenly. We fix this by resetting posts with deeper footings — typically 42 inches — and using adjustable hinge hardware that can be tuned without re-pouring concrete. In severe cases, we install steel post sleeves or relocate to a more stable pier foundation.
Yes, if you want remote access logs, temporary codes for service workers, and alerts when your gate opens unexpectedly. LiftMaster’s myQ and DoorKing’s remote management systems integrate well with Keller’s generally strong residential internet infrastructure. We install these with proper antenna placement and cellular backup options for properties with spotty coverage near the back of larger lots.
No. Shaking indicates a bent track, worn v-groove wheels, or a rack gear that’s binding — all common in Keller where clay heave and debris in the track slot accelerate wear. On a 2010 installation, you’re also likely due for operator gear inspection; the rack-and-pinion drive may be skipping teeth. We can usually diagnose this in one visit and have parts in the truck for same-day repair if the frame and track are salvageable.
Properly sized and maintained residential operators last 12–15 years in Keller’s climate; undersized or poorly installed units fail in 7–10. The difference is load calculation and post stability. We’ve replaced 15-year-old LiftMaster units that were still running because they were correctly spec’d and installed on stable footings, and we’ve seen 8-year-old units destroyed by clay heave and overload. Annual maintenance — lubrication, limit-switch checks, post plumb verification — extends life significantly.
Written by Dennis Price, Owner at Everest Gate Repair Service Dallas Fort Worth, serving Keller and North Texas since 2013.